1330

Summary

Product identification

The 1330, 60Hz series is a non-clog submersible pump designed for efficient pumping of clean water, surface water, and wastewater containing solids. It is designed for sustained efficiency over time.

Model variants include:

• Non-explosion proof version: 1330.181
• Explosion proof version: 1330.090

Head types available:

• H – High head
• L – Low head
• M – Medium head
• S – Super high head

Installation types supported:

• Free-standing: Portable semipermanent, wet well arrangement with hose coupling or flange for connection to the discharge pipeline.
• Wet-well: Semipermanent, wet well arrangement with the pump installed on two guide bars. The connection to the discharge is automatic.

Operating limits

• Liquid temperature: Maximum 40°C (104°F)
• Depth of immersion: Maximum 20 m (65 ft)
• pH of the pumped liquid: 5.5 – 14
• Liquid density: Maximum 1100 kg/m³

Electrical

• Motor type: Squirrel-cage induction motor
• Frequency: 60 Hz
• Power supply: 3-phase
• Starting method:
  • Direct on-line
  • Star-delta
  • Variable Frequency Drive (VFD)
• Number of starts per hour: Maximum 15
• Code compliance: IEC 60034-1
• Voltage variation without overheating: ±10%, if it does not run continuously at full load
• Voltage imbalance between phases: Maximum 2%
• Stator insulation class: F (155°C [311°F])
• Cables:
  • Direct-on-line start or Y/D start with two cables: Flygt SUBCAB® - a heavy duty 4 cores motor power cable with two twisted pair screened control cores. Conductor insulation rating of 90°C, allowing for increased current. Superior mechanical strength and high abrasion and tear resistant. Chemical resistant within pH 3-10 and ozone, oil, and flame resistant. Used up to 70°C water temperature. Cables < 10 mm² with unscreened control cores.
  • Y/D start: Flygt SUBCAB® - a heavy duty 7 cores motor power cable with two twisted pair screened control cores. Conductor insulation rating of 90°C, allowing for increased current. Superior mechanical strength and high abrasion and tear resistant. Chemical resistant within pH 3-10 and ozone, oil, and flame resistant. Used up to 70°C water temperature. Cables < 7G6 mm² with unscreened control cores.
• Monitoring equipment (Motor): Thermal contacts opening temperature 140°C (284°F)

Mechanical / hydraulic

Major Parts Materials:

• Major castings: Cast iron, gray (ASTM 30B, EN GJL-200)
• Pump housing: Cast iron, gray (ASTM 30B, EN GJL-200)
• Impeller: Cast iron, gray (ASTM 30B, EN GJL-200)
• Lifting eye bolt: Steel electro zinc coated (EN 10084 - C15E)
• Lifting handle: Stainless steel (AISI 304, EN 1.4301)
• Shaft: Stainless steel (AISI 431, EN 1.4057+QT800)
• Screws and nuts: Stainless steel, A2 (AISI 304, EN 1.4301, 1.4306, 1.4307, 1.4311)
• O-rings: Nitrile rubber (NBR) 70° IRH
• Oil, part no 901752: Medical white oil of paraffin type. Fulfills FDA 172.878 (a).

Mechanical Seals:

• Inner seal: Corrosion resistant cemented carbide (WCCR)/Corrosion resistant cemented carbide (WCCR)
• Outer seal: Corrosion resistant cemented carbide (WCCR)/Corrosion resistant cemented carbide (WCCR)

Surface Treatment:

• Black or blue two-component high-solid top coating.

Options:

• Leakage sensor in the stator housing (FLS)

Accessories:

• Installation equipment (sold in kits)
• Mechanical accessories such as discharge connections, adapters, and hose connections
• Electrical accessories such as pump controller, control panels, starters, monitoring relays, and cables

Performance Data

The document includes performance curves and detailed tables for various configurations (High head, Low head, Medium head, Super high head) at 460 V, 60 Hz, 3-phase. These tables specify rated power (kW/hp), impeller number, revolutions per minute (rpm), rated current (A), start current (A), power factor (cos φ), and applicable installation types (Free-standing, Wet-well). Star-delta starting current is 1/3 of Direct on-line starting current.

See the official PDF for exact tabulated values and performance curves.

---

Disclaimer: This summary is based on extracted text and may not include all figures, footnotes, or the latest revisions from the complete OEM PDF datasheet. Contractual data must always match the specific OEM PDF revision used for the project.

Official datasheet (PDF)

Lenntech datasheet mirror