1330

Summary

Product identification

The 1330, 50Hz is a non-clog submersible pump designed for efficient pumping of clean water, surface water, and wastewater containing solids. It is available in non-explosion proof (1330.181) and explosion proof (1330.090) versions.

Model variants are categorized by head:

• H – High head
• L – Low head
• M – Medium head
• S – Super high head

Installation types include:

• Free-standing: Portable semipermanent, wet well arrangement with hose coupling or flange for connection to the discharge pipeline.
• Wet-well: Semipermanent, wet well arrangement with the pump installed on two guide bars. The connection to the discharge is automatic.

Operating limits

• Liquid temperature: Maximum 40°C (104°F)
• Depth of immersion: Maximum 20 m (65 ft)
• pH of the pumped liquid: 5.5 – 14
• Liquid density: Maximum 1100 kg/m³

Electrical

• Motor type: Squirrel-cage induction motor
• Frequency: 50 Hz
• Power supply: 3-phase
• Starting method:
  • Direct on-line
  • Star-delta
  • Variable Frequency Drive (VFD)
• Number of starts per hour: Maximum 15
• Code compliance: IEC 60034-1
• Voltage variation without overheating: ±10%, if it does not run continuously at full load
• Voltage imbalance between phases: Maximum 2%
• Stator insulation class: F (155°C [311°F])
• Cables: Flygt SUBCAB® heavy duty motor power cables.
  • Direct-on-line start or Y/D start with two cables: 4 cores with two twisted pair screened control cores. Conductor insulation rating of 90°C. Chemical resistant within pH 3-10 and ozone, oil, and flame resistant. Used up to 70°C water temperature. Cables < 10 mm² with unscreened control cores.
  • Y/D start: 7 cores with two twisted pair screened control cores. Conductor insulation rating of 90°C. Chemical resistant within pH 3-10 and ozone, oil, and flame resistant. Used up to 70°C water temperature. Cables < 7G6 mm² with unscreened control cores.
• Monitoring equipment:
  • Motor thermal contacts opening temperature: 140°C (284°F)

Performance Data (400 V, 50 Hz, 3-phase)

• H – High head (Impeller No. 441, 442, 443):
  • Rated power: 18 kW (24 hp) to 24 kW (32 hp)
  • Revolutions per minute: 1455 to 1465 rpm
  • Rated Current: 34 A to 45 A
  • Start current: 251 A
  • Power Factor: 0.85 to 0.88
  • Installation: Free-standing (FS), Wet-well (WW)
• L – Low head (Impeller No. 601, 603, 605):
  • Rated power: 10 kW (13.4 hp) to 15 kW (20 hp)
  • Revolutions per minute: 965 to 980 rpm
  • Rated Current: 22 A to 30 A
  • Start current: 166 A
  • Power Factor: 0.76 to 0.85
  • Installation: Free-standing (FS), Wet-well (WW)
• M – Medium head (Impeller No. 421, 422, 423):
  • Rated power: 16 kW (21 hp) to 24 kW (32 hp)
  • Revolutions per minute: 1455 to 1470 rpm
  • Rated Current: 31 A to 45 A
  • Start current: 251 A
  • Power Factor: 0.83 to 0.88
  • Installation: Free-standing (FS), Wet-well (WW)
• S – Super high head (Impeller No. 262, 264):
  • Rated power: 22 kW (30 hp) to 24 kW (32 hp)
  • Revolutions per minute: 2920 to 2925 rpm
  • Rated Current: 38 A to 42 A
  • Start current: 269 A
  • Power Factor: 0.93
  • Installation: Free-standing (FS), Wet-well (WW)

Note: Star-delta starting current is 1/3 of Direct on-line starting current. Performance curves are available in the official PDF.

Mechanical / hydraulic

Materials (Major parts except mechanical seals)

• Major castings: Cast iron, gray (ASTM 30B, EN GJL-200)
• Pump housing: Cast iron, gray (ASTM 30B, EN GJL-200)
• Impeller: Cast iron, gray (ASTM 30B, EN GJL-200)
• Lifting eye bolt: Steel electro zinc coated (EN 10084 - C15E)
• Lifting handle: Stainless steel (AISI 304, EN 1.4301)
• Shaft: Stainless steel (AISI 431, EN 1.4057+QT800)
• Screws and nuts: Stainless steel, A2 (AISI 304, EN 1.4301, 1.4306, 1.4307, 1.4311)
• O-rings: Nitrile rubber (NBR) 70° IRH
• Oil, part no 901752: Medical white oil of paraffin type. Fulfills FDA 172.878 (a).

Mechanical seals

• Inner seal: Corrosion resistant cemented carbide (WCCR)/ Corrosion resistant cemented carbide (WCCR)
• Outer seal: Corrosion resistant cemented carbide (WCCR)/ Corrosion resistant cemented carbide (WCCR)

Surface treatment

• Black or blue two-component high-solid top coating.

Options

• Leakage sensor in the stator housing (FLS)

Accessories

• Installation equipment (sold in kits)
• Mechanical accessories such as discharge connections, adapters, and hose connections
• Electrical accessories such as pump controller, control panels, starters, monitoring relays, and cables

---

Disclaimer: This summary is based on extracted text and may not include all figures, footnotes, or the latest revisions from the complete OEM PDF datasheet. Contractual data must always match the specific OEM PDF revision used on the project.

Official datasheet (PDF)

Lenntech datasheet mirror