CSM RE8040-BR

Summary

Product identification

The RE8040-BR is a high rejection reverse osmosis (RO) element featuring a thick feed spacer, designed for brackish water applications.

• Membrane type: Thin-Film Composite
• Membrane material: Polyamide (PA)
• Element configuration: Spiral-Wound, FRP Wrapping

Product water

• Permeate flow rate: 6,000 GPD (22.7 m³/day)
  • Permeate flow rate for each element may vary but will be no more than 15%.
• Nominal salt rejection: 99.75%
• Minimum salt rejection: 99.4%
• Effective membrane area: 380 ft² (35.3 m²)

Performance Test Conditions: The stated product performance is based on data taken after 30 minutes of operation at the following conditions:

• 2,000 mg/L NaCl solution
• 225 psig (1.5 MPa) applied pressure
• 15% recovery
• 77 °F (25 °C)
• pH 6.5–7.0

Operating limits

• Max. Pressure Drop / Element: 15 psi (0.1 MPa)
• Max. Pressure Drop / 240” Vessel: 60 psi (0.41 MPa)
• Max. Operating Pressure: 600 psi (4.14 MPa)
• Max. Feed Flow Rate: 75 gpm (17.0 m³/hr)
• Min. Concentrate Flow Rate: 16 gpm (3.6 m³/hr)
• Max. Operating Temperature: 113 °F (45 °C)
• Operating pH Range: 2.0–11.0
• CIP pH Range: 1.0–13.0
• Max. Turbidity: 1.0 NTU
• Max. SDI (15 min): 5.0
• Max. Chlorine Concentration: < 0.1 mg/L

Feed water

Design Guidelines for Various Water Sources (Flux in gfd):

• Wastewater Conventional (SDI < 5): 8–12 gfd
• Wastewater Pretreated by UF/MF (SDI < 3): 10–14 gfd
• Seawater, Open Intake (SDI < 5): 7–10 gfd
• Seawater, Beach Well (SDI < 3): 8–12 gfd
• Surface Water (SDI < 5): 12–16 gfd
• Surface Water (SDI < 3): 13–17 gfd
• Well water (SDI < 3): 13–17 gfd
• RO permeate (SDI < 1): 21–30 gfd

Saturation Limits (Using Antiscalants):

• Langlier Saturation Index (LSI): <+1.5
• Stiff and Davis Saturation Index (SDSI): <+0.5
• CaSO₄: 230% saturation
• SrSO₄: 800% saturation
• BaSO₄: 6,000% saturation
• SiO₂: 100% saturation

Mechanical / hydraulic

• Model Name: RE 8040-BR
• Dimensions:
  • A: 40.0 inch (1,016 mm)
  • B: 8.0 inch (201 mm)
  • C: 1.12 inch (28 mm)
• Weight: 15 kg
• Part Numbers:
  • Inter-connector: 40000308
  • Brine Seal: 40000309
• Fit: All RE8040 elements fit nominal 8.0 inch (201 mm) I.D. pressure vessels.
• Accessories: Each membrane element is supplied with one brine seal, one interconnector (coupler), and four o-rings.

General Handling Procedures

• Elements contained in the boxes must be kept dry at room temperature (7–32°C; 40–95°F) and should not be stored in direct sunlight.
• If the polyethylene bag is damaged, a new preservative solution (sodium bisulfite) must be added and air-tight sealed to prevent drying and biological growth.
• Permeate from the first hour of operation should be discarded to flush out the preservative solution.
• Elements should be immersed in a preservative solution during storage, shipping, and system shutdowns to prevent biological growth and freezing. The standard storage solution contains 1% by weight sodium bisulfite or sodium metabisulfite (food grade). For short-term storage (i.e., one week or less), 1% by weight sodium metabisulfite solution is adequate for preventing biological growth.
• Keep elements moist at all times after initial wetting.
• Avoid excessive pressure and flow spikes.
• Only use chemicals compatible with the membrane elements and components.
• Permeate pressure must always be equal to or less than the feed/concentrate pressure. Damage caused by permeate back pressure voids the element limited warranty.

---

Disclaimer: This summary is based on the provided text extract and may not include all figures, footnotes, or the latest revisions from the original OEM PDF. For contractual data, always refer to the specific OEM PDF revision used on the project.

Official datasheet (PDF)

PDF datasheet