MB 40 TR

Summary

Product Identification

This document describes the DuPont™ IntegraTec™ MB 40 TR S module, a P series pressurized PES ultrafiltration module designed for T-Rack™ S configurations (previously known as dizzer XL 1.5 MB 40 ST).

• Part Number / GMID: IN-5103 / 12071529
• Mode of Filtration: In-Out Pressurized
• Membrane Type: Multibore™
• Membrane Material: PESm
• Nominal Membrane Pore Size: 0.02 µm
• Module Operating Process: Dead-end
• Housing Material: PVC-U, white

Key Applications:

• Municipal wastewater
• Industrial water
• Wastewater reuse
• Ideal for height-restricted or containerized filtration solutions

Key Features:

• Proven Multibore™ PES Fibers:
  • Exceptional physical strength and chemical resistance.
  • High colloidal particulate, bacteria, and virus log removal rate.
  • Unique design for high solids loads.
  • Optional coagulation can enhance the removal of algae and organics.
• Optimized Module Design:
  • Innovative end-cap design to suit T-Rack™ S concept with simple assembly and scalability.
  • Robust materials for long lifetime.
  • Easy installation and low maintenance.
  • All wetted parts corrosion-free.

Mechanical / Hydraulic

• Active Membrane Area: 40 m² (431 ft²)
• Module Length Including T-Piece (L): 1,879 mm (74.0 inch)
• Module Diameter (D): 250 mm (9.8 inch)

Weight and Volume:

• Shipping Weight (Module Only): 47 kg (104 lbs.)
• Weight Empty (Module and Corresponding Frame): 59 kg (131 lbs.)
• Weight Filled (Module and Corresponding Frame): 124 kg (272 lbs.)
• Hold-Up Volume Feed (CIP): 31 L (8.1 gal)
• Hold-Up Volume Membrane Structure (CIP): 16 L (4.2 gal)
• Hold-Up Volume Filtrate (CIP): 30 L (8.0 gal)

T-Rack™ Configuration: The datasheet provides detailed tables for T-Rack™ S configurations in both 2 Rows and 4 Rows, listing the number of modules, T-Rack™ unit part number, length, and total membrane area. See the official PDF for exact tabulated values.

Operating Limits

Suggested Operating Conditions:

• Operating Temperature Range: 1 - 40 °C (34 - 104 °F)
• Operating pH: 3 - 11
• Cleaning pH: 1 - 13
• Typical Filtration TMP: 0.1 - 0.6 bar (1.5 - 8.7 psi)
• Typical Backwash TMP: 0.3 - 2.0 bar (4.4 - 29.0 psi)
• Backwash Flux: 230 L/(m²h) (135 gfd)
• Backwash Flow: 9.2 m³/h (40.5 gpm)

Operating Limits (Maximum):

• Rate of Temperature Change: 5 °C/min (9 °F/min)
• Inlet Pressure: 5 bar (73 psi)
• Rate of Pressure Change: 0.5 bar/sec (7.3 psi/sec)
• Filtration TMP: 1.5 bar (22 psi)
• Backwash TMP: 3.0 bar (44 psi)
• Filtration Flux: 180 L/(m²h) (106 gfd)
• Filtration Flow: 7.2 m³/h (31.7 gpm)
• Backwash Flux: 300 L/(m²h) (176 gfd)
• Particle Size: 300 µm
• Exposure NaOCl: ≤ 250,000 ppm x h (at pH ≥ 9.5)
• Concentration NaOCl: 500 ppm

General Guidelines

• Avoid any abrupt pressure variations during start-up, operation, shutdown, cleaning, or other sequences to prevent possible membrane damage. The maximum allowable pressure change is 0.5 bar/s.
• For assembly, refer to the latest version of the DuPont™ IntegraTec™ Pressurized UF In-Out P Series Assembly Instructions for T-Rack™ Manual (Form No. 45-D02230-en).
• Failure to strictly follow operating limits and guidelines may void any warranty.
• During extended system shutdowns, a storage solution must be introduced into the membrane modules to control biological growth. Refer to the DuPont™ IntegraTec™ Pressurized UF Out-In Module Preservation Instruction Manual (Form No. 45-D02946-en) for detailed information.
• Certified drinking water modules require specific conditioning procedures prior to producing potable water. For operating parameters, refer to the DuPont™ IntegraTec™ Pressurized UF In-Out P Series Process and Design Guidelines (Form No. 45-D02234-en).
• Drinking water modules may be subject to additional regulatory restrictions in some countries. Check local regulatory guidelines and application status before use.
• Flushing must be done according to the DuPont™ IntegraTec™ Pressurized UF Out-In Module Rinsing Procedure (Form No. 45-D02947-en).

---

Disclaimer: This summary is based on extracted text and may not include all figures, footnotes, or the latest revisions present in the official OEM PDF. Contractual data must always match the specific OEM PDF revision used for the project.

Official datasheet (PDF)

Lenntech datasheet mirror