MB 80 TR

Summary

Product Identification

• Product: DuPont™ IntegraTec™ MB 80 TR Pressurized PES UF Module for T-Rack™
• Previous Name: dizzer XL 0.9 MB 80 WT
• Form No.: 45-D02243-en, Rev. 4 (December 2025)
• Part Number / GMID: IN-5109 / 12071530

Key Applications

• Municipal drinking water
• Desalination RO pretreatment
• Industrial utility water
• Industrial wastewater reuse
• Ideal for large systems

Key Features

• Proven Multibore™ PES Fibers:
  • Exceptional physical strength and chemical resistance.
  • High colloidal particulate, bacteria and virus log removal rate.
  • Unique design for high solids loads.
  • Optional coagulation can enhance the removal of algae and organics.
• Optimized Module Design:
  • Innovative end-cap design to suit T-Rack™ concept with simple assembly and scalability.
  • Robust materials for long lifetime.
  • Easy installation and low maintenance.
  • All wetted parts corrosion free.

Mechanical / Hydraulic

• Mode of Filtration: In-Out Pressurized
• Membrane Type: Multibore™
• Membrane Material: PESm
• Nominal Membrane Pore Size: 0.02 µm
• Module Operating Process: Dead-end
• Housing Material: PVC-U, white
• Active Membrane Area: 80 m² (861 ft²)
• Module Length Including T-Piece (L): 2,101 mm (82.7 inch)
• Module Diameter (D): 250 mm (9.8 inch)

Weight and Volume

• Shipping Weight (Module Only): 54 kg (120 lbs.)
• Weight Empty (Module and Corresponding Frame): 67 kg (147 lbs.)
• Weight Filled (Module and Corresponding Frame): 133 kg (292 lbs.)
• Hold-Up Volume Feed (CIP): 33 L (8.7 gal)
• Hold-Up Volume Membrane Structure (CIP): 20 L (5.4 gal)
• Hold-Up Volume Filtrate (CIP): 31 L (8.3 gal)

Operating Limits

Suggested Operating Conditions

• Operating Temperature Range: 1 - 45 °C (34 - 113 °F)
• Operating pH: 2 - 12
• Cleaning pH: 1 - 13
• Typical Filtration TMP: 0.1 - 0.6 bar (1.5 - 8.7 psi)
• Typical Backwash TMP: 0.3 - 2.0 bar (4.4 - 29.0 psi)
• Backwash Flux: 230 L/(m²h) (135 gfd)
• Backwash Flow: 18.4 m³/h (81.0 gpm)

Maximum Operating Limits

• Rate of Temperature Change: 5 °C/min (9 °F/min)
• Inlet Pressure at max 40°C: 5 bar (73 psi)
• Rate of Pressure Change: 0.5 bar/sec (7.3 psi/sec)
• Filtration TMP: 1.5 bar (22 psi)
• Backwash TMP: 3.0 bar (44 psi)
• Filtration Flux: 180 L/(m²h) (106 gfd)
• Filtration Flow: 14.4 m³/h (63.4 gpm)
• Backwash Flux: 300 L/(m²h) (176 gfd)
• Particle Size: 300 µm
• Exposure NaOCl: ≤ 500,000 ppm x h (at pH ≥ 9.5)
• Concentration NaOCl: 2,000 ppm
  • Note: NaOCl exposure limits at lower pH are dependent on water type and are project specific.

T-Rack™ Configuration

The datasheet provides detailed tables for T-Rack™ configurations, including module counts, rack part numbers, lengths, and total membrane areas for Single-Sided and Double-Sided connections to manifolds, in both 2 Rows and 4 Rows configurations. See the official PDF for exact tabulated values.

General Information

• Avoid any abrupt pressure variations during start-up, operation, shutdown, cleaning or other sequences to prevent possible membrane damage. The maximum pressure change allowable is 0.5 bar/s.
• For assembly, refer to the latest version of the DuPont™ IntegraTec™ Pressurized UF In-Out P Series Assembly Instructions for T-Rack™ Manual (Form No. 45-D02230-en).
• If operating limits and guidelines given in this bulletin are not strictly followed, any warranty will be null and void.
• To control biological growth during extended system shutdowns, a storage solution must be introduced into the membrane modules. For detailed information, see the DuPont™ IntegraTec™ Pressurized UF Out-In Module Preservation Instruction Manual (Form No. 45-D02946-en).

Regulatory Note

• Certified drinking water modules require specific conditioning procedures prior to producing potable water. For operating parameters, refer to the DuPont™ IntegraTec™ Pressurized UF In-Out P Series Process and Design Guidelines (Form No. 45-D02234-en).
• Drinking water modules may be subjected to additional regulatory restrictions in some countries. Check local regulatory guidelines and application status before use.
• Flushing needs to be done according to the DuPont™ IntegraTec™ Pressurized UF Out-In Module Rinsing Procedure (Form No. 45-D02947-en).

Disclaimer: This summary is based on extracted text and may miss figures, footnotes, or the latest revisions. Contractual data must always match the OEM PDF revision used on the project.

Official datasheet (PDF)

Lenntech datasheet mirror