Datasheet summary
Targa 8072-742-20-PM10 Hollow Fiber
Engineering summary from PDF text extraction for Targa 8072-742-20-PM10 Hollow Fiber. Verify every value with the OEM datasheet.
Summary
Product identification
- Product Type: TARGA® PM10 HOLLOW FIBER CARTRIDGES
- Application: 8-inch Industrial Water Ultrafiltration Cartridges
- Membrane Chemistry: Proprietary semi-permeable polysulfone
- Membrane Type: PM10
- Housing Shell/End Caps: Proprietary polysulfone
- Fiber Support Netting: Polypropylene/Polyethylene
- Permeate Collection Tube: PVC
- Potting Material: Proprietary epoxy compound
- Preservative: Glycerin
Product Specifications
| Model | Part Number | Nominal MWCO | Production Range gpm (m³/hr) |
|---|---|---|---|
| TARGA® 8072-742-20-PM10 | 0720413 | 10,000 | 48.2 (10.9) - 22.7 (5.2) |
| TARGA® 8072-367-43-PM10 | 0720415 | 10,000 | 23.4 (5.3) - 11.0 (2.5) |
Note: Higher production can be expected for post IX/RO polishing applications.
Operating limits
- Maximum Pressure (water): 45 psi (3.0 bar) @ 104º F (40º C) or less
- Temperature Range: 32º F (0º C) - 104º F (40º C)
- Maximum Production Transmembrane Pressure: 30 psi (2.1 bar)
- Maximum Backflush Transmembrane Pressure: 20 psi (1.4 bar)
- Maximum Total Chlorine @ 77º F (25º C) or lower: 200 ppm @ 9.5 pH or higher during intermittent backflush
- Maximum Total Chlorine Contact: 200,000 ppm-hrs cumulative
Consult KMS Process Engineering Group for specific applications.
Mechanical / hydraulic
Nominal Dimensions
| Model | Fiber Diameter (ID) | Membrane Area | D Inches (mm) | L Inches (mm) |
|---|---|---|---|---|
| TARGA® 8072-742-20-PM10 | 0.020 inch (0.5 mm) | 742 ft² (68.9 m²) | 8.4 (213) | 72 (1829) |
| TARGA® 8072-367-43-PM10 | 0.043 inch (1.1 mm) | 367 ft² (34.1 m²) | 8.4 (213) | 72 (1829) |
Assembly Components
- 8” HF Cartridge (1 each)
- Leveling Hardware (Screw ½ ” X 13) (2 each) – Part Number: 1002443
- Leveling Hardware (Nut ½ “ X 13) (2 each) – Part Number: 1002443
- 8” Coupling Set (gasket included) (2 each) – Part Number: 0151303
- O-Ring, Permeate Adapter (8 each) – Part Number: 0211022
- Permeate Adapter (2 each) – Part Number: 1002655
- 2” Coupling Set (gasket included) (2 sets) – Part Number: 0151304 / 0151261
- Kit Process Pass for 8” cartridge – Part Number: 0220158
Storage Conditions
- New cartridges:
- Impregnated with glycerin. Remove glycerin before initial use with a rinse, followed by a caustic wash, and then a caustic/chlorine wash.
- Store in original shipping containers and crates:
- Indoors, out of direct sunlight.
- At temperatures between 50 – 85 °F (10 – 30 °C).
- At relative humidity below 70%.
- In a horizontal position.
- Used cartridges:
- Cleaned, rinsed, and impregnated before storage with one of the following solutions:
- Glycerin @ 80 – 100%
- Phosphoric acid @ pH 2 – 3
- Benzoic acid or sodium benzoate @ 1,000 ppm
- Sodium bisulfite or sodium metabisulfite @ 1,000 – 5,000 ppm
- Cartridges stored in sodium bisulfite or sodium metabisulfite should be flushed with clean water and impregnated with fresh solution at six-month intervals.
- Once impregnated, leave cartridges on the system with all valves closed, or remove from the system and seal in plastic bags.
- Storage conditions described for new cartridges also apply to used cartridges.
- Cartridges must be drained, rinsed, and cleaned after storage per the pre-startup cleaning instruction sheet.
- Cleaned, rinsed, and impregnated before storage with one of the following solutions:
Disclaimer: This summary is based on the provided text extract and may not include all figures, footnotes, or the latest revisions from the official OEM PDF datasheet. Contractual data must match the specific OEM PDF revision used on the project.
Official datasheet (PDF)
Curated from selected public technical reference material for discovery and preliminary comparison. This summary is not a substitute for a current certified manufacturer datasheet. Verify revisions and design limits before use.