ABCOR INDUCOR 12 HFM 251 ICV

Summary

Product identification

• Part Number (KPN): 0712510
• Membrane Chemistry: PVDF
• Membrane Type: HFM (neutral charge)
• Membrane Area: 45.5 ft² (4.2 m²)
• Molecular Weight Cut-Off: 100,000 Dalton (nominal)
• Construction: Thirty (30) ½” diameter tubules in a PVC shell
• Face Plate: ABS
• Gasket: VITON®

Operating limits

• Maximum inlet pressure: 90 psi @ 119 °F (6.2 bar @ 48 °C)
• Maximum operating temperature: 122 °F (50 °C) at 84 psi max
• Maximum permeate side back pressure: 3 psi (0.2 bar)
• Minimum outlet pressure: 5 psi (0.3 bar)
• Maximum feed side pressure drop: 7.5 psi @ 119 °F (0.5 bar @ 48 °C)
• Allowable pH - Continuous Exposure: 2.0 – 10.0 @ 119 °F (48 °C)
• Allowable pH - Short Term Exposure: 1.5 – 10.5 @ 119 °F (48 °C)

Consult with Industrial Process Technology Group for specific applications.

Feed flow vs. pressure drop

Data based on water at 77 °F and specific gravity of 1.0.

Nominal dimensions

• A: 144 inches (3658 mm)
  • 1” Ø (2.54 cm) permeate outlet (2 per module, 180° aligned)
• B: 8 inches (203.2 mm)
  • VICTAULIC® Style 4” IPS Rolled Groove
• C: 4½ inches (114.3 mm)

Ancillary parts

KMS recommends that these membranes be used with KMS supplied ancillary parts. Sealing is provided by o-rings and gaskets. No additional sealing compound or tape is recommended for use on threaded connections.

INDUCOR™ Module Process Pass Kits One Process Pass Kit contains:

• Two Permeate Port Saddle Assemblies
• Two 4” Coupling Assemblies Available in two styles of Permeate Port Saddle:
• 1” IPS Socket Style Pass Kit KPN 0211875
• 1” FNPT Threaded Style Pass Kit KPN 0211885

Module Assembly Components

• 4” Process U-Bend KPN 0020614
• 4” Coupling Assembly KPN 0125575 (Each assembly contains all the needed fastening hardware and one Viton® seal)
• Permeate Port Saddle Assembly
  • 1” IPS Socket Style KPN 0020616
  • 1” FNPT Threaded Style KPN 0020618 (Each assembly contains all the needed fastening hardware and one Viton® o-ring)

Membrane incompatibility

Prior to exposing the membrane to any chemical, the chemical should be reviewed by Koch Membrane Systems. Aside from the listed chemicals below, synthetic coolants, semi-synthetic coolants, kerosenes, naphtha, gasoline, and floc polymers may affect membrane performance.

Chemicals that should be avoided include the following:

• Aprotic Solvent (e.g., Dimethyl Formamide, Dimethyl Acetamide, N-Methyl Pyrolidine, etc.)
• Chlorinated Solvents (e.g., Methylene Chloride, Chloroform, Carbon Tetrachloride, etc.)
• Ketones (e.g., Acetone, Diacetone Alcohol, etc.)
• Silicones or Silicone based Defoamers (e.g., Siloxane)

Disclaimer: This extraction may miss figures, footnotes, or revisions from the original document. Contractual data must match the OEM PDF revision used on the project.

Official datasheet (PDF)

PDF datasheet