SUEZ

Typical dosage range: 3 to 6 mg/L (ppm) · Maximum dosage for potable applications: 10 mg/L (ppm)

Hypersperse MDC700 is a liquid antiscalant and antifoulant designed for membrane separation systems including RO, NF, and UF.

Typical dosage range: 1 to 6 mg/L

Hypersperse MDC701 is a liquid antiscalant and antifoulant designed for use in membrane separation systems to control scale and particulate fouling.

Typical dosage range: 3 to 6 mg/L · Potable applications maximum dosage: 10 mg/L

Hypersperse MDC702 is a liquid antiscalant and antifoulant designed to control scale precipitation and reduce particulate fouling in membrane separation systems.

Typical dosage range: 1.5 to 5 mg/L · Maximum dosage for potable applications: 12 mg/L

Hypersperse MDC704i is a liquid antiscalant and antifoulant designed to control scale and particulate fouling in membrane separation systems like RO, NF, and EDR.

Typical dosage range: 3 to 6 ppm (mg/L) · Maximum dosage for potable applications: 8 ppm (mg/L)

Hypersperse MDC706 is a liquid antiscalant and antifoulant designed to control scale precipitates and particulate fouling in membrane separation systems.

Temperature <30 °C: Maximum Dilution 10% · Temperature 30-35 °C: Maximum Dilution 25% · Temperature >35 °C: Maximum Dilution 50%

Hypersperse MDC707 is a liquid antiscalant and antifoulant designed to control scale and reduce particulate fouling in membrane separation systems.

Maximum dosage for potable applications: 10 mg/L (or 10 ppm) · Typical dosage range: 3 to 6 mg/L

Hypersperse MDC708 is a non-phosphorous liquid antiscalant/antifoulant formulated to control scale and reduce fouling in membrane separation systems.

Typical Dosage Range: 2 to 6 mg/L · Maximum Dosage (Potable Applications): 10 mg/L

Hypersperse MDC711 is a liquid antiscalant and antifoulant designed to control scale and particulate fouling in membrane separation systems.

Typical Dosage Range: 0.4 to 0.6 mg/L

Hypersperse MDC712 is a liquid antiscalant and antifoulant designed to prevent scale and fouling in membrane separation systems.

Typical Dosage Range: 0.5 to 3 mg/L · Maximum Dosage for Potable Applications: 10 mg/L · Dose Rate Determination: Recommended to use Argo Analyzer 4.0 simulation software for specific system and water chemistry. Contact local SUEZ representative for optimal feed point and dosage

Hypersperse MDC714 is a liquid antiscalant and antifoulant designed for membrane separation systems in seawater, brackish water, and water reuse applications.

Typical dosage range: 2 to 6 mg/L · Potable applications maximum dosage: 10 mg/L

Hypersperse MDC754 is a liquid antiscalant and antifoulant for membrane separation systems that controls scale and particulate fouling.

Typical dosage range: 1 to 6 mg/L

Hypersperse MDC759 is a liquid antiscalant and antifoulant designed to prevent scale and particulate fouling in membrane separation systems.

Typical Dosage Range: 0.5 to 3 mg/L · Dose Determination: The Argo Analyzer 4.1 simulation software is recommended to determine the adequate dose rate based on specific water chemistry and system design

Hypersperse MDC761 is a liquid antiscalant and antifoulant designed to control scale and fouling in membrane separation systems like RO, NF, and EDR.

Typical Dosage Range: 2 to 6 mg/L

Hypersperse MDC772 is a liquid antiscalant and antifoulant designed for membrane separation systems like reverse osmosis and nanofiltration.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

Hypersperse MDC775 is a liquid antiscalant and antifoulant developed for membrane separation systems like reverse osmosis and nanofiltration.

Typical dosage range: 2 to 10 mg/L · Maximum dosage for potable applications: 10 mg/L

Hypersperse MDC776 is a liquid antiscalant and antifoulant designed for membrane separation systems to control scale and particulate fouling.

Maximum dosage: 50 ppm · Typical dosage range: 10 to 30 ppm

Hypersperse AF250B is a liquid antiscalant and antifoulant designed for membrane separation systems. It effectively controls calcium carbonate up to LSI +2.50.

Typical dosage range: 4 to 12 ppm

Hypersperse AF250UL is a liquid antiscalant and antifoulant designed for industrial membrane separation systems like RO, NF, and UF.

Typical dosage range: 3 to 6 ppm (mg/L) · Maximum dosage for potable applications: 10 ppm (mg/L)

Hypersperse MSI410 is a liquid antiscalant and antifoulant certified for potable water production. It effectively controls silica, calcium, and sulfate scaling.

Typical dosage range: 3 to 6 mg/l

Hypersperse MDC120 is a liquid antiscalant certified for potable water production that controls scale precipitates and disperses foulants on membrane surfaces.

Typical Dosage Range: 2 to 6 mg/L

Hypersperse MDC150 is a liquid antiscalant and antifoulant designed to control scale and particulate fouling in membrane separation systems.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

Hypersperse MDC200 is a liquid antiscalant designed to prevent inorganic scale formation and particulate fouling in reverse osmosis and nanofiltration systems.

Storage Temperature: Store at temperatures above its freezing point of -30°F (-34°C) to maintain product integrity · Viscosity: 2000 cps @ 25°C. A pump capable of handling high viscosity products is required

Butaclean 4900 is a non-aqueous, 100% silicone compound used as a general-purpose antifoam and defoamer in extractive separation processes.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

Butaclean 4903 is a general-purpose silicone emulsion antifoam and defoamer for preventing and controlling foam in aqueous process applications.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

Butaclean 4905 is a non-silicon based, 100% active anti-foam/defoamer fluid designed to control foaming in synthetic rubber manufacturing.

Initial Concentration: Recommended 0.5% (range 0.3% to 1%) · Storage Temperature: Moderate temperatures (7 to 38°C). Protect from freezing

BetzDearborn AE1115 is a liquid emulsion anionic, low charge density, high molecular weight polymeric flocculant used for industrial water treatment clarification.

Initial Concentration: Recommended initial makedown solution concentration is 0.5% (range 0.3 to 1%) · Temperature: Store at moderate temperatures (7 to 38°C). Protect from freezing

BetzDearborn AE1125 is a liquid emulsion anionic, medium charge density, high molecular weight polymeric flocculant used in industrial water treatment for clarification...

Initial Concentration: Recommended 0.5% (range 0.3% to 1%) · Storage Temperature: 7 to 38°C. Protect from freezing

BetzDearborn AE1128 is a liquid emulsion anionic flocculant used as a coagulant aid in industrial water clarification, thickening, and sludge dewatering.

Initial Concentration: Recommended initial makedown solution concentration is 0.5% (range 0.3% to 1%) · Storage Temperature: Store at moderate temperatures (7 to 38°C)

BetzDearborn AE1138 is an anionic, high molecular weight liquid emulsion flocculant designed for industrial water clarification, thickening, and sludge dewatering.

Initial Concentration: Recommended initial makedown concentration is 0.5% (range 0.3% to 1%) · Temperature: Store at moderate temperatures (7 to 38°C). Protect from freezing

BetzDearborn AE1700 is a liquid emulsion polymeric flocculant used in industrial water treatment for clarification, thickening, and sludge dewatering. This anionic.

Initial Concentration: Recommended initial makedown concentration is 0.5% (range 0.3 to 1%) · Storage Temperature: Store at moderate temperatures (7 to 38°C). Protect from freezing

BetzDearborn AE1703 is a liquid emulsion anionic, high charge density, high molecular weight polymeric flocculant used as a coagulant aid or flocculant for solids...

Maximum Practical Solution Concentration: 0.5% by weight · Dosage: Proper treatment levels depend on application severity and site-specific conditions. Use in accordance with SUEZ control procedures · Materials of Construction: Stainless steel, polyethylene, or PVC are recommended for tanks, pumps, and piping. Mild steel is acceptable only if corrosion product contamination is not critical

BetzDearborn AP1140P is a high molecular weight, anionic polymer flocculant and sludge conditioning aid for enhanced liquid-solids separation.

Storage Temperature: Store at moderate temperatures of 4 to 32°C

BetzDearborn AS1002 is a liquid, high molecular weight, strongly anionic flocculant used in industrial water treatment for clarification, thickening, and softening.

Typical dosage range: 5 to 10 ppm (mg/L) · Maximum dosage for potable applications: 50 ppm (mg/L)

SoliSep MPT104 is a liquid, anionic polymeric flocculant designed for membrane pretreatment, functioning as a coagulant aid to remove particulate matter, turbidity.

Maximum Solution Concentration: 0.5% by weight

Novus AP1782 is a high molecular weight, anionic powder polymer used as a flocculant or sludge conditioning aid in diverse wastewater and industrial applications.

Initial Make-down Concentration: Recommended at 0.5% (range 0.3% to 1%) · Storage Temperature: 7 to 38°C. Protect from freezing

Novus AE1784 is a liquid anionic emulsion polymer designed for use as a coagulant aid or flocculant in industrial water clarification and sludge dewatering.

Further dilution to approximately 0.05% by weight (10: 1 ratio) enhances performance in most applications

Novus AP1780 is a high molecular weight, medium charge density anionic powder polymer used as a flocculant or sludge conditioning aid.

Storage Temperature: Store at moderate temperatures (4-32 °C) · Short-Term Materials: Flexible PVC tubing (e.g., Tygon), Buna-N, and Neoprene rubber may be suitable for short-term installations · Materials to Avoid (or use with caution): Mild steel and copper alloys should only be used if discoloration by corrosion products is tolerable

BetzDearborn CE1163 is a liquid, high molecular weight cationic emulsion polymer used for solid/liquid separation and sludge dewatering.

Suitable Materials: Type 304 stainless steel, polyethylene, and rigid PVC for tanks, tubing, piping, and pumps. Viton and fluorosilicon rubbers for pump components and hose linings · Storage Temperature: Moderate temperatures (4-32 °C) · Limited Use Materials: Flexible PVC tubing (e.g., Tygon®), Buna-N, and Neoprene rubber for short-term installations. Mild steel and copper alloys only if discoloration by corrosion products is acceptable

BetzDearborn CE1165 is a liquid cationic emulsion polymer designed for solid/liquid separation and sludge dewatering applications.

Temperature: Store at moderate temperatures (4-32 °C) · Protection: Protect from freezing and rapid or repeated temperature changes that may cause condensation

BetzDearborn CE1169 is a liquid, high molecular weight cationic polymer designed for solid/liquid separation applications and sludge dewatering.

Maximum Solution Concentration: 0.5% by weight · Dosage: Treatment levels depend on the severity of the problem and site-specific conditions. Product use must follow SUEZ established control procedures

BetzDearborn CP1152 is a high molecular weight, low charge density cationic polymer functioning as a sludge conditioning agent or flocculant in surface and wastewater...

Maximum Solution Concentration: 0.5% by weight · Dosage: Treatment levels depend on the severity of the problem and specific installation conditions. Follow SUEZ established control procedures

BetzDearborn CP1153 is a high molecular weight, medium charge density cationic polymer used as a sludge conditioning agent or flocculant in wastewater treatment.

Maximum solution concentration: 0.5% by weight

BetzDearborn CP1154 is a high molecular weight, low charge density cationic polymer designed for sludge conditioning and flocculation in surface and wastewater treatment.

Maximum Solution Concentration: 0.5% by weight

BetzDearborn CP1155 is a high molecular weight, cationic polymer used as a sludge conditioning agent or flocculant in various industrial water treatment applications.

Maximum Solution Concentration: 0.5% by weight · Temperature Limit: Avoid water temperatures exceeding 37°C · For general applications, further dilution to approximately 0.05% by weight (10: 1 dilution) is recommended

BetzDearborn CP1156 is a high molecular weight, high charge density cationic polymer used as a sludge conditioning agent and flocculant for surface and wastewater...

Maximum Solution Concentration: 0.5% by weight

BetzDearborn CP1157 is an online instrument or sensor product for water systems, best compared by measured parameter, range, mounting style, and signal interface.

Maximum Solution Concentration: 0.5% by weight · Dosage: Proper treatment levels depend on the specific installation and are determined by SUEZ control procedures

BetzDearborn CP1159 is a medium molecular weight, low charge density cationic polymer used as a sludge conditioning agent or flocculant.

Concentration range for proper inversion: 0.5% to 1.0% · Suitable materials for tanks, tubing, piping, and pumps: Type 304 or 316 stainless steel, Teflon, and PE/PP · Storage temperature: 4 to 32°C. Protect from freezing

Novus CE1647 is a liquid, high molecular weight cationic emulsion polymer designed for solid/liquid separation and sludge dewatering in industrial wastewater applications.

Storage temperature: 45 to 100°F (7 to 38°C)

Novus CE1655 is a liquid, high molecular weight cationic emulsion polymer designed for solid/liquid separation and sludge dewatering.

Storage Temperature: 4 to 32°C. Protect from freezing · Bulk Container Protection: Insulate against extreme heat, cold, and temperature variation · In wet areas: Use sand, grit, or suitable material for traction

Novus CE1657 is a liquid cationic emulsion polymer for solid/liquid separation and sludge dewatering in industrial wastewater. It is suitable for use with stainless steel.

Inversion Concentration: 0.5% to 1.0% in a continuous system · Storage Temperature: 4 to 32°C. Protect from freezing · Wet areas: Use sand, grit, or suitable material for traction

Novus CE1681 is a cationic emulsion polymer designed for solid/liquid separation and sludge dewatering in various industrial wastewater applications.

Storage Temperature: Store at moderate temperatures of 4°C to 32°C. Protect from freezing

Novus CE1682 is a liquid, high molecular weight cationic emulsion polymer designed for solid/liquid separation and sludge dewatering in various industrial wastewater...

Concentration for Inversion: 0.5% to 1.0% in a continuous system · Suitable Materials: Type 304 or 316 stainless steel, Teflon, PE/PP for tanks, tubing, piping, and pumps. Viton and fluoro-silicon type rubbers for pump components and hose linings · Storage Temperature: 4°C to 32°C. Protect from freezing

Novus CE1683 is a cationic emulsion polymer designed for solid/liquid separation and sludge dewatering in various industrial wastewater applications.

Make-down Concentration: 0.5% to 1.0% for inversion · Storage Temperature: 4 to 32°C. Protect from freezing

Novus CE1684 is a liquid cationic emulsion polymer designed for solid/liquid separation and sludge dewatering in various industrial wastewater applications.

Storage Temperature: 4 to 32°C. Protect from freezing and extreme temperature variations · Less Preferred Materials: Mild steel and copper alloys may be used if discoloration from corrosion products is acceptable. Stock solutions should use the same materials

Novus CE1685 is a high molecular weight, high charge density cationic emulsion polymer designed for solid/liquid separation and sludge dewatering in various industrial...

Satisfactory materials: Type 304 or 316 stainless steel, Teflon, PE/PP for tanks, tubing, piping, and pumps · Storage temperature: 4 to 32°C. Protect from freezing

Novus CE1686 is a liquid, high molecular weight cationic emulsion polymer for solid/liquid separation and sludge dewatering. It is easily fed as a liquid emulsion.

Make-down Concentration: Prepare a 0.5% to 1.0% solution in the make-down unit · Application Concentration: Further dilute to approximately 0.2% before the point of application · Storage Temperature: 4 to 32°C (39 to 89°F). Protect from freezing

Novus CE2653E is a liquid, high molecular weight cationic emulsion polymer designed for solid/liquid separation and sludge dewatering in industrial wastewater.

Concentration: 0.5% to 1.0% for proper inversion · Suitable Materials: Type 304 or 316 stainless steel, Teflon, rigid PVC for tanks, tubing, piping, and pumps. Viton and fluorosilicon type rubbers for pump components and hose linings · Temperature: Store between 45 to 100°F (7 to 38°C). Protect from freezing

Novus CE2654 is a liquid, high molecular weight cationic emulsion polymer for solid/liquid separation and sludge dewatering.

Storage Temperature: Store at moderate temperatures of 4 to 32°C (39 to 89°F). Protect from freezing

Novus CE2654E is a liquid, high molecular weight cationic emulsion polymer designed for solid/liquid separation and sludge dewatering in industrial wastewater...

Concentration range for proper inversion: 0.5% to 1.0% · Suitable materials: Type 304 or 316 stainless steel, Teflon, rigid PVC · Storage Temperature: 4 to 32°C (39 to 89°F). Protect from freezing

Novus CE2655E is a liquid, high molecular weight cationic emulsion polymer designed for solid/liquid separation and sludge dewatering in industrial wastewater.

Storage Temperature: Moderate temperatures (4-32 °C) · Protection: Protect from freezing and rapid or repeated temperature changes

Novus CE2657 is a liquid high molecular weight cationic emulsion polymer designed for solid/liquid separation applications including sludge dewatering and wastewater...

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

Novus CE2666 is a liquid, high molecular weight, cationic emulsion polymer designed for solid/liquid separation and sludge dewatering applications.

Storage Temperature: Store at moderate temperatures (4-32 °C) · Protection: Protect from freezing and rapid or repeated changes in temperature (which can cause condensation)

Novus CE2667E is a liquid, high charge density cationic emulsion polymer designed for solid/liquid separation and sludge dewatering applications.

Suitable Materials: Type 304 stainless steel, polyethylene, and rigid PVC for tanks, tubing, piping, and pumps. Viton and fluorosilicon rubbers for pump components and hose linings · Storage Temperature: Moderate temperatures (4–32 °C) · Limited Use Materials: Flexible PVC tubing (e.g., Tygon\), Buna-N, and Neoprene rubber for short-term installations. Mild steel and copper alloys only if discoloration by corrosion products is acceptable

Novus CE2672E is a liquid cationic emulsion polymer designed for solid/liquid separation and sludge dewatering.

Store at moderate temperatures: 40 to 90°F (4 to 32°C)

Novus CE2672 is a liquid, high molecular weight cationic emulsion polymer designed for liquid/solids separation and sludge dewatering of industrial wastewaters.

Suitable materials for tanks, tubing, piping, and pumps: Type 304 stainless steel, polyethylene, and rigid PVC · Storage Temperature: Moderate temperatures (4-32 °C) · Material Handling (Stock Solutions): Use the same materials of construction as for the neat polymer. Positive displacement pumps (e.g., gear or piston pumps) can be used for metering

Novus CE2680E is a liquid cationic emulsion polymer designed for solid/liquid separation, sludge dewatering, and wastewater clarification.

Storage Temperature: Store at moderate temperatures between 40 to 90°F (4 to 32°C) · Protection: Protect from freezing and rapid or repeated temperature changes that may cause condensation

Novus CE2680 is a high molecular weight cationic emulsion polymer designed for liquid/solids separation and sludge dewatering in industrial wastewater.

Temperature: Store at moderate temperatures (4-32 °C) · Protection: Protect from freezing and rapid or repeated changes in temperature to prevent condensation

Novus CE2681E is a liquid, cationic emulsion polymer designed for solid/liquid separation and sludge dewatering.

Temperature: Store at moderate temperatures (4-32 °C) · Materials to Avoid (unless discoloration is acceptable): Mild steel and copper alloys · Protection: Protect from freezing and rapid or repeated temperature changes which can cause condensation

Novus CE2682E is a liquid, cationic emulsion polymer designed for solid/liquid separation and sludge dewatering. It is suitable for use with 304 stainless steel.

Satisfactory Materials: Type 304 stainless steel, polyethylene, rigid PVC · Storage Temperature: Store at moderate temperatures (4-32 °C) · Short-Term Use Materials: Flexible PVC tubing (e.g., Tygon\), Buna-N, Neoprene rubber

Novus CE2684E is a liquid, cationic emulsion polymer for solid/liquid separation and sludge dewatering. It can be handled with stainless steel, polyethylene, or PVC.

Storage Temperature: Store at moderate temperatures (4-32 °C) · Protection: Protect from freezing and rapid or repeated temperature changes that may cause condensation

Novus CE2688E is a liquid, high molecular weight cationic emulsion polymer designed for solid/liquid separation and sludge dewatering.

Concentration range for proper inversion: 0.5% to 1.0% · Recommended materials: Type 304 or 316 stainless steel, Teflon, and rigid PVC for tanks, tubing, piping, and pumps · Storage Temperature: 4 to 32°C (39 to 89°F). Protect from freezing

Novus CE2695 is a liquid cationic emulsion polymer used for solid/liquid separation and sludge dewatering in industrial wastewater applications.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

Kleen MCT103 is a low pH liquid formulation designed to remove metal hydroxides and calcium carbonate scales from membrane separation systems.

Dose rate determination: The Argo Analyzer custom software package is available to assist in dose rate determination. Contact your local SUEZ representative for specific conditions and optimum dosage rates

Kleen MCT403 is a low pH powder membrane cleaner designed to remove metal hydroxides and calcium carbonate foulants from RO, NF, and UF membranes.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

Kleen MCT411 is a powdered, high pH cleaning formulation designed for reverse osmosis, nanofiltration, and ultrafiltration membranes. It is suitable for polysulfone.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

Kleen MCT442 is a low pH, powdered membrane cleaner designed for reverse osmosis, nanofiltration, and ultrafiltration systems.

Materials Compatibility: Use corrosion-resistant equipment for storage, preparation, and use

Kleen MCT503 is a low pH liquid membrane cleaner designed to remove scale from RO, NF, UF, and MF membranes.

Materials Compatibility: Use corrosion-resistant equipment such as PVC for storage and preparation. Pumping materials should also be corrosion resistant

Kleen MCT511E is a high pH liquid cleaner formulated for removing organics, silt, and particulate deposits from polysulfone, fluorocarbon.

0.5% concentration: pH 11.34, Conductivity 2,032 µS · 1.0% concentration: pH 11.51, Conductivity 3,590 µS · 1.5% concentration: pH 11.62, Conductivity 5,063 µS

Kleen MCT515 is a liquid alkaline membrane cleaner formulated with proprietary buffered alkaline and detergent agents to remove organic foulants like oils and bioproteins.

Operating Pressure: Less than 60 psig (4.2 kg/cm²) · Compatibility: Do not use on CA membranes

Kleen MCT515E is a buffered alkaline liquid cleaner designed for removing organic foulants, biofilm, and iron from membrane surfaces.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

BetzDearborn IEC2 is a liquid ion exchange resin cleaner designed to remove metallic and inorganic foulants like iron, copper, and hardness salts.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

Ion exchange resins can become fouled by organic and inorganic compounds present in water. This fouling can lead to: Blocked ion exchange sites.、Resin clumping.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

BetzDearborn PQ682 is a liquid blend designed for internal boiler water treatment to control deposit formation by precipitating hardness.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

BetzDearborn DCL30 is a liquid sodium bisulfite solution used to remove chlorine from reverse osmosis and ultrafiltration feedwaters.

Dosage: 4.44 ppm of BetzDearborn DCL32 are required to remove 1 ppm of chlorine (measured as total chlorine) · Dosage Limitation: Application dosages should be limited by the chlorine demand. An excess of sodium bisulfite may increase the incidence of microbiological growth in membrane systems

BetzDearborn DCL32 is a liquid sodium bisulfite solution used as a cost-effective dechlorinating agent for potable and food-grade membrane applications.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

BetzDearborn DCL95 is a high-purity sodium metabisulfite powder used for removing free and combined chlorine from reverse osmosis and ultrafiltration feedwaters.

Typical dosage range: 2 to 10 mg/l · Specific Gravity (for calculation): 1.05

SoliSep MPT150 is a liquid organic coagulant formulated to enhance colloidal solids removal in sand and multimedia filters.

Typical dosage range: 1 to 6 mg/l

SoliSep MPT170 is a liquid organic coagulant designed to improve colloidal solids removal by sand and multimedia filters, particularly for open seawater intakes.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

BioMate MBC781 is an EPA registered, non-oxidizing membrane biocide for sanitizing RO and UF systems and membranes.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

BioMate MBC881 is a non-oxidizing biocide for sanitizing reverse osmosis and ultrafiltration systems. It is formulated for compatibility with polyamide, polysulfone.

Target conductivity range for this dilution: 3,800 to 4,100 micromhos

Kleen ENV903 is a low pH liquid membrane cleaner formulated to remove metal hydroxides and calcium carbonate scales from various membrane types.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

Kleen ENV907 is an environmentally friendly, neutral pH liquid formulation for cleaning cellulose acetate reverse osmosis (RO) membranes.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

Liquiclean 103 is a low pH liquid membrane cleaner designed to remove scale from various membrane types. It is buffered for effective pH over a range of dilutions.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

Organic materials and suspended solids in incoming water can accumulate on membrane surfaces, creating an environment conducive to microbiological activity and fouling.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

Kleen MCT107 is a neutral pH liquid membrane cleaner designed to remove organic foulants and particulate deposits from cellulose acetate reverse osmosis membranes.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

Kleen MCT400 is a powdered membrane biofouling and organic cleaner recommended for Desal and Brackish water membranes. It contains organic acids, an anionic surfactant.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

This cleaner is indicated for use when organic materials and suspended solids accumulate on the membrane surface, leading to reduced water flow.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

Kleen MCT407 is a low pH liquid membrane cleaner designed to remove scale from RO, NF, UF, and MF membranes.

Solution pH: Approximately 11.5 to 12.0 · Circulation Pressure: Less than 60 psig (4.1 bar). Pressure should be low enough to prevent permeate production during cleaning · Temperature: Enhanced performance at elevated temperatures. Contact your SUEZ representative for recommended levels if not provided by the membrane manufacturer

Kleen MCT412 is a high pH, powdered membrane cleaner designed for removing organic and particulate deposits from RO and NF membranes. This formulation is low-foam.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

MemChem MCT201 is a solid, low pH membrane cleaner for nanofiltration, ultrafiltration, microfiltration, and reverse osmosis systems.

Recommended cleaning solution pH: 9.0 to 11.0, or as recommended by the membrane manufacturer. pH can be adjusted with Betz MPH2500 (upward) or Betz MPH5000 (downward) · Temperature: Normally below 104º F (40º C). Enhanced performance at elevated temperatures · Circulation Pressure: Less than 60 psig (4.2 kg/cm²)

MemChem MCT505 is a liquid cleaner formulated with NPE-free surfactants, detergents, and chelating agents to remove organic foulants and hard-water stains from membrane...

Typical Dosage: 5 to 50 ppm (mg/L) based on system circulation rate · Temperature Limit: Stable at temperatures up to 121°C (250°F) · Compatibility: DO NOT MIX with other process or water treatment chemicals unless compatibility has been checked and approved by SUEZ Product Management

Butaclean 4701 is a dispersant designed to control solid and hydrophobic substance deposition in butadiene and elastomer units.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

BioMate SAN9361 is a broad-spectrum non-oxidizing biocide for controlling microbiological growth in brewery pasteurizers and other heat exchange water systems.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

BioMate SAN9363 is an isothiazoline-based microbicide for controlling microbiological populations in brewery pasteurizers, cooling towers, and other water systems.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

BioMate SAN9383 is a liquid surfactant-based product designed for microbiological fouling control in food and beverage process systems.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

BioMate SAN9451 is a broad-spectrum non-oxidizing biocide for microbiological control in various process water systems like brewery pasteurizers and heat exchangers.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

BioMate SAN9380 is a liquid precursor that generates hypobromous acid for controlling microbial populations in various water systems when oxidized.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

BioMate 5702 is a liquid chlorine microbiological control agent for open evaporative cooling systems, designed to prevent biofouling and control Legionella bacteria.

Dosage: 25 L (30 kg) per 1000 L of water in the system · Pressure: Maintain 50% pressure during the boil-out period. Alternate pressure to promote circulation

Kleen BC9520 is a liquid concentrated alkaline treatment designed to remove oil, grease, and other foreign materials from waterside boiler surfaces.

Recommended cleaning solution pH: 10 to 11 (higher pH is acceptable and may provide improved MB control) · Concentration: Can range from 0.5% to 2.0% as necessary to achieve desired solution strength and cleaning performance, while meeting pH requirements · Cleaning solution temperature: Typically maintained above 90°F (32°C) and less than 120°F (49°C)

Kleen EG8664 is a low-foaming, strongly alkaline liquid cleaner designed for removing organic contaminants from egg shells during on-line processing.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

Kleen EG8666 is a concentrated liquid organic acidic cleaner for removing debris, iron oxide, and hardness-based scale from holding tanks.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

MemChem MCT210 is a liquid acid membrane cleaner designed to dissolve inorganic scale and metal oxides from ultrafiltration and micro-filtration systems. This no-foaming.

Materials Compatibility: Use corrosion-resistant equipment (e.g., PVC) for storage and preparation. Pumping materials in contact with diluted product should also be corrosion-resistant

MemChem MCT253 is a liquid acid membrane cleaner designed to remove metal oxides and other foulants from filtration systems.

Materials Compatibility: Use corrosion-resistant equipment, such as PVC, for storage and preparation. Pumping materials in contact with the diluted product should also be corrosion-resistant

MemChem MCT254 is a liquid acid membrane cleaner designed for RO, NF, and UF/MF systems to dissolve inorganic scale and metal oxides. It is a non-foaming.

Cleaning Solution pH: Target range is 11.0 to 12.0, or as recommended by the membrane manufacturer · Target Conductivity: 2,400 to 3,000 micromhos for the recommended dilution · Cleaning Solution Temperature: Do not allow the temperature to exceed 95°F (34°C)

Kleen MCT405 is a liquid alkaline membrane cleaner designed for removing organic foulants from Polyamide (PA) membrane elements in potable water applications.

Target Conductivity: 2,800 to 3,500 micromhos for the recommended dilution · Membrane Compatibility: For use on PA membrane elements only. Do not use on CA membranes

Kleen MCT406 is a liquid caustic blend with surfactants and detergents designed for cleaning PA membrane elements and removing iron, aluminum, organics, and biofilm.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

Butaclean 4702 is a concentrated, water-based corrosion inhibitor designed to protect against various acids and oxygen by forming a protective film on metal surfaces.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

Butaclean 4703 is a concentrated, water-based corrosion inhibitor formulated with organic filming inhibitors to protect equipment in butadiene, isoprene.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

JelCleer JPC700 is a high-molecular weight coagulant activator designed to enhance the performance of JelCleer 1000 filtration media.

Typical Dosing Range: 1 to 6 ppm (mg/L) · Storage Temperature: 40 to 90°F (4 to 32°C)

SoliSep MPT130 is a liquid polymeric coagulant designed for removing colloidal turbidity, emulsified materials, and color from surface and recycled waters.

Selection cues: recommended dose · pH and specific gravity · water chemistry and compatibility

SoliSep MPT132 is a liquid, low molecular weight polymeric coagulant designed for colloidal material removal from surface and process waters.

Typical Dosing Range: 1 to 10 ppm (mg/L) · Storage Temperature: Store at moderate temperatures of 40 to 90 °F (4 to 32 °C)

SoliSep MPT134 is a liquid polymeric coagulant designed for removing colloidal materials from surface waters and recycled process waters.